turbo lag
-
- Donating Member
- Posts: 120
- Joined: Sat Feb 28, 2009 5:24 pm
- Location: perth western australia
turbo lag
t2 back on road with rebuilt,balanced engine front mount intercooler, blitz boost controller,doesn't start to pull till about 3500 rpm so is slow off the mark very disappointing to drive especially when you read about turbocab smoking in second[well done] the mechanic thinks the lag may be from the long and daggy intercooler piping?any thoughts[my t1 turbo cab is much quicker off the mark]
-
- Forum Enthusiast
- Posts: 270
- Joined: Tue Jan 20, 2004 8:47 am
- Location: Dunedin
Re: turbo lag
When you rebuilt the motor did you rebuild the turbo unit?
Turbo units like to run hot, so a cold start wont spool up quick.
The Intercooler provides the cool air that expands in the CC.
The length may affect it but I would look to the turbo unit itself?
Does it smoke much idling at the lights etc or when caning it?
Turbo units like to run hot, so a cold start wont spool up quick.
The Intercooler provides the cool air that expands in the CC.
The length may affect it but I would look to the turbo unit itself?
Does it smoke much idling at the lights etc or when caning it?
craybait wrote:t2 back on road with rebuilt,balanced engine front mount intercooler, blitz boost controller,doesn't start to pull till about 3500 rpm so is slow off the mark very disappointing to drive especially when you read about turbocab smoking in second[well done] the mechanic thinks the lag may be from the long and daggy intercooler piping?any thoughts[my t1 turbo cab is much quicker off the mark]
- bmgjet
- Donating Member
- Posts: 220
- Joined: Fri Dec 03, 2010 3:23 pm
- Location: New Zealand New Plymouth
- Contact:
Fitted a new boost controller to my car today.
With the controller off it doesn't reach 12psi till 3500rpm.
Suspect its because the waste gate slowly opens instead of staying closed till I reach the desired boost.
With it turned on works the same as other boost controller and reaches 15psi 2900rpm. But with out spikes now.
With the controller off it doesn't reach 12psi till 3500rpm.
Suspect its because the waste gate slowly opens instead of staying closed till I reach the desired boost.
With it turned on works the same as other boost controller and reaches 15psi 2900rpm. But with out spikes now.
what size wheels/tyres are you running have you increased the size recently?
perhaps try wiring the waste gate flapper hard shut and very carefully go for a drive and see if it boosts up quicker,at the very worst it will just fuel cut when it overboosts.
my intercooler piping is relatively long and 50mm in diameter and mine still boosts up fairly quick and as you said smokes em up on 13 in wheels and chalky old tyres but that did require a violent downshift and a frantic right foot aplication
perhaps try wiring the waste gate flapper hard shut and very carefully go for a drive and see if it boosts up quicker,at the very worst it will just fuel cut when it overboosts.
my intercooler piping is relatively long and 50mm in diameter and mine still boosts up fairly quick and as you said smokes em up on 13 in wheels and chalky old tyres but that did require a violent downshift and a frantic right foot aplication
-
- Forum Addict
- Posts: 609
- Joined: Mon Apr 01, 2002 2:02 am
- Location: Newcastle, NSW Australia
-
- Forum Regular
- Posts: 69
- Joined: Fri May 08, 2009 8:59 am
t2 should be smoking easy
thats suprising to hear that you are experiancing so much lag
definately would be taking almost all the fun out of that lil car!
any chance of some pics of what your running?
definately would be taking almost all the fun out of that lil car!
any chance of some pics of what your running?
- James
- Moderator / Donating Member
- Posts: 3092
- Joined: Wed Apr 09, 2003 1:59 pm
- Location: Putaruru
- Contact:
When you work out the physics of it, the volume of your intercooler piping makes next to no difference. Consider a couple of meters of 50mm tubing, thats ~4 litres in volume. A city engine at 3000rpm uses ~1800 litres per minute, or 30 litres a second of air, assuming 100% volumetric efficiency. So while it will make a small difference, its unlikely to be significant if your piping is free of restrictions.
It sounds like you might have a leaky wastegate, or leaky turbo (does it sound like a tractor?)
I suggest you do what turbocab said and wire the gate shut, and see what that does.
It sounds like you might have a leaky wastegate, or leaky turbo (does it sound like a tractor?)
I suggest you do what turbocab said and wire the gate shut, and see what that does.
-
- Donating Member
- Posts: 120
- Joined: Sat Feb 28, 2009 5:24 pm
- Location: perth western australia
turbo lag
turbo was rebuilt running 13 inch wheels,car was on dyno when not quite run in since then have added a plumb back in blow off valve with some dodgy looking piping so will try all the above suggestions thanks guys
-
- Donating Member
- Posts: 120
- Joined: Sat Feb 28, 2009 5:24 pm
- Location: perth western australia
turbo lag
about to tackle the above problem,step one is to put stock intercooler on,then work from there.Thanks again for the input.The recent hunting problem rectified by finding throttle body not closing,the mechanic had to re torque the head,so suspect the little prick at radiator shop fanged the new not run engine when cold and had a backfired
Re: turbo lag
craybait wrote:t2 back on road with rebuilt,balanced engine front mount intercooler, blitz boost controller,doesn't start to pull till about 3500 rpm so is slow off the mark very disappointing to drive especially when you read about turbocab smoking in second[well done] the mechanic thinks the lag may be from the long and daggy intercooler piping?any thoughts[my t1 turbo cab is much quicker off the mark]
Hey brother,
What was exactly done to the motor in the rebuild? Were the cams modified? Are they standard pistons or forged? What size intercooler and from what model? What turbo was rebuilt, the standard turbo? If it was the standard turbo, was it rebuilt to exact standard specification? Was the block bored out? Sorry if info has been posted elsewhere. Im new here and still catching up.
-
- Donating Member
- Posts: 120
- Joined: Sat Feb 28, 2009 5:24 pm
- Location: perth western australia
turbo lag
motor complete rebuild,original pistons machined for isuzu rings everthing balanced including cluth,the culprit is the turbo it had a$ 1500 flow/rebuild job on it so it boosts from 4000 so it flys from 4500 to 6000.Very narrow rev band ,I think the previous owner aimed for drag racing.We changed back to original intercooler ,no difference.
Who is online
Users browsing this forum: No registered users and 103 guests